联系人: 雷先生 (来电时请说是从北极星看到我的)
手机:18702110275
电话: 021-69153629
地址: 江苏省无锡市江阴市南闸镇东盟园区5号
应用场景
高压母排、电缆搭接处因老化、松动等原因造成接触电阻增大,当大电流通过时会产生
热量,容易导致设备烧毁或突然停电等事故。
从安全角度,推荐使用无线测温方案。采用 ATE400 安装在母排、电缆搭接处,将采集
到的温度数值,通过无线信号传输到 ASD500 智能操控显示端。
产品方案
1.1 产品概述
1.1 Product Introduction
ATE系列无线测温传感器根据 《NB/T 42086-2016无线测温装置技术要求》 开发,可用于3~35kV户内开关柜,包括中置柜、手车柜、固定柜、环网柜等多种开关柜;也可用于0.4kV低压柜,包括固定柜,抽屉柜等。无线测温传感器可安装于柜内任何发热点上,利用无线数据传输技术实时发送监测数据,再通过接收装置将温度数据传输到显示装置或者远程监控系统。
ATE series wireless temperature measuring sensor has been developed in compliance with Specification for Wireless Temperature Measuring equipment, NB/T 42086-2016. It is suitable for 3-35kV indoor switchgears, including built-in switchgears, handcart switchgears, fixed switchgears and loop-net switchgears. It is also suitable for 0.4kV low-voltage switchgears such as fixed switchgears and drawer switchgears. The wireless temperature sensors can be installed at any heating point in switchgears, the device utilizes the wireless data transmission technology for real-time transmission of monitored temperature data. In addition, it can be transmitted to display device or remote intelligent monitoring system.
1.2 型号说明
1.2 Type Introduction
1.3 技术指标
1.3 Technical Features
1.4 产品安装
1.4 Product Installation
无线温度传感器共有多种型号,分别对应磁吸固定、螺栓固定、表带固定、合金片固定等安装方式。
There are several types of wireless temperature sensors and mounting methods correspondingly, i.e. Magnetic , bolted , belt and alloy chip fixing.
1.4.1 外形尺寸
1.4.1 Shape Size
1.4.2标签说明
1.4.2 Label Instructions
1.4.2.1 ATE传感器搭配ASD/ARTM-Pn装置
1.4.2.1 ATE sensor with ASD/ARTM-Pn device
如果安装ATE100M/ATE100/ATE200/ATE400/ATE100P/ATE200P,其组号应与显示装置ASD/ARTM-Pn的标签组号一致,安装位置依照标签文字安装,“编码:1A”为安装第一个A相,“编码:1B”为安装第一个B相,以此类推。
If the sensor is ATE100M/ATE100/ATE200/ATE400/ATE100P/ATE200P, the number behind “组号(Group):” should be the same as ASD/ARTM-Pn, the sequence of installation is base on the label, “编码(Code):1A” is first one on the phase A, “编码(Code):1B” is first one on the phase B,and so on.
注意:出厂时包装箱内无线温度传感器与显示装置已配对,不可以与其他显示装置或无线温度传感器混用,无线温度传感器按照标签安装。
Notice: wireless temperature sensors and display device in the package have been matched before delivery. Do not use them with other display device or other wireless temperature sensors together. Please installing them with label on the sensor.
1.4.2.2 ATE传感器搭配ATC600-C
1.4.2.2 ATE sensor with ATC600-C
如图所示,如果安装ATE100M/ATE100/ATE200/ATE400/ATE100P/ATE200P/ATE300P,其组号应与ATC600-C的组号一致,安装位置依照标签文字安装,“编码:001”建议安装在第一个柜子的第一个测温点,再依次按照测温点顺序安装。
According to the above pictures, If the sensor is ATE100M/100/200/400/100P/200P/300P, the group number of ATE must be same as the group number of ATC600-C and the installation order is base on the label. The code of each sensor is used to distingguish each sensor from same group. “编码(code): 001” is recommended to be installed on the first temperature measuring point of the first cabinet, and then installed other sensors in this order.
1.4.2.3 ATE300M传感器搭配ATC600-M收发器
1.4.2.3 ATE300M sensor with ATC600-M coordinator
如果安装ATE300M传感器,其组号应与ATC600-M的组号一致,安装位置依照标签文字安装,“编码:001”建议安装在第一个柜内,再依次按照测温点顺序安装。
If the sensor is ATE300M, the group number of ATE must be same with the group number of ATC600-M and the installation order is base on the label. The code of each sensor is used to distingguish each sensor from same group. “编码(code): 001” is recommended to be installed on the first cabinet,
若有特殊情况,请联系相关工程师进行沟通解决。
In case of any special situation, please contact the relevant engineers for communication.
1.4.3 安装方法
1.4.3 Installation Method
1.4.3.1 ATE100M安装方法
1.4.3.1 ATE100M Installation Method
ATE100M磁吸式无线测温传感器适用于铁质的电气节点或设备表面。
The magnetic wireless sensor ATE100M is suitable for iron electrical nodes or equipment surfaces.
磁吸式无线温度传感器ATE100M结构说明:
Structure introduction of ATE100M:
1 —— 无线温度传感器主体The core of wireless temperature sensor ATE100M
2—— 测温部位Thermo-sensitive part
3 —— 电池开关battery switch
直接吸附在铁质测温点处,安装前打开电池开关,电源指示灯闪烁两次。安装实例见下图:
Adsorbed directly at the iron temperature measuring point, open the battery switch before installation, the power indicator flashes twice. The installation examples see images below.
1.4.3.2 ATE100安装方法
1.4.3.2 ATE100 Installation Method
ATE100螺栓式无线测温传感器适用于电缆与母排搭接处,电缆与隔离刀闸搭接处。
The bolted type wireless sensor ATE100 is suitable for use at joints between cable and bus bar and joints between cable and disconnector.
ATE100螺栓式无线温度传感器结构说明:
ATE100 structure introduction:
1 —— 无线温度传感器主体The core of wireless temperature sensor ATE100
2 —— 测温部位Thermo-sensitive part
3 —— 电池开关battery switch
拆下安装位置搭接处的螺丝,将传感器固定在安装位置,对准合金底板的开孔,然后旋紧螺丝固定,安装前打开电池开关,电源指示灯闪烁两次。安装实例见下图:
Remove the screw from the joints, and fixing the sensor on the position with the hole on the alloy baseplate, then tighten the screw, open the battery switch before installation, the power indicator flashes twice. The installation examples see images below.
1.4.3.3 ATE200安装方法
1.4.3.3 ATE200 Installation Method
ATE200表带式无线测温传感器适用于断路器动触头、静触头、电缆接头、母排等处。
The strap-secured type called ATE200 is suitable for use at moving contacts and fixed contacts of breaker, cable joints and bus bar.
表带式无线温度传感器结构说明:
ATE200 structure introduction:
1 —— 无线温度传感器主体,测温探头在背面The core of wireless temperature sensor ATE200, temperature measuring probe is on the other side
2 —— 表带及锁扣strap and hasp
3 —— 电池开关battery switch
将传感器主体固定在安装位置,将表带绕过安装母排或者触头穿过表带,表带头收紧,最后将表带尾用锁扣锁紧。表带过长可以剪掉多余部分,表带过短可以联系我司增订。安装前打开电池开关,电源指示灯闪烁两次。安装实例见下图:
注:ATE200可安装静触头,铜排,电缆头。
Fixing the body of sensor on the position, then strapping it on the bus bar or breaker contact and frapping it through the hole on the strap, fixing the strap by hasp. Clipping the strap if it is too long when finished, if it is too short, contacting us for strap parts before installation. Open the battery switch before installation, the power indicator flashes twice.The installation examples see images below.
Note: ATE200 can be installed with fixed contact, copper plate and cable head.